As the original rim of the Indian Scout cannot be widened, we have produced a 3-piece custom rim in the original design (Indian Scout Bobber). The rim can be installed plug & play in the rear swing arm that we have widened. The pulley offset has already been taken into account here so that the belt can run past the rear wheel in conjunction with the offset pulley (can be ordered here in the store). The rear wheel is supplied ready to fit, only the brake disk and ABS trigger disk from the original wheel need to be screwed on, the original shock absorber with pulley mount and pulley can still be used. Scope of delivery: Ready-to-install rear wheel, size 8.5 x 17, surface depending on variant TÜV sample certificate of an identical vehicle for individual TÜV approval

3-part custom motorcycle wheel type 10 from our company, available for almost all motorcycles - whether single or double arm swingarm. (Wheels for single-sided swingarms are usually asymmetrical, i.e. the outer rim base is narrower than the inner rim base. This can only be determined after measuring the original rims) Important: We manufacture the rims ourselves, which means we can respond to detailed customer requests. So if you have a special design idea - we can make it a reality! We offer here in the store the most common variants of our rims, but are able to produce special designs of all kinds. So if you are interested, please send us an email or give us a call. We need the original wheels of your vehicle for the measurement. Please remove brake discs and tires, we also don't need the sprocket carrier for the measurement. Simply send them well packed by mail to RF-Biketech GmbH, Mühlweg 10, 97720 Nuedlingen, Germany. Once we have taken the measurements, we will return the wheels to you intact by mail. The rims are made of high-strength aluminum using CNC technology here inhouse. We mill the inner part of the rim completely ourselves, the rim beds are delivered to us. The inner part and the rim beds are then screwed together (VA screws) and glued. The tires are mounted tubeless. The hub adapters for the rims are included in the price. Sprocket carrier of the original rims is further used. Otherwise the wheels are plug & play ready to install, no new wheel spacers or other modifications necessary (of course only if original sizes are chosen). If you choose wider wheels, rear swingarm or triple clamps have to be changed as well - we offer wide swingarms as well as our own triple clamps here in the store. Just give us a call or write an email if you have any questions, we'll be happy to advise you! Surface info: Rims can be delivered high gloss polished, bicolor (rims are coated in color and the contours of the inner part then milled again, so that these edges and pockets appear again in aluminum silver) or also in RAL powder coated. We offer here in the store only black-matte and black-glossy, other colors quite simply ask by mail and we send you an offer. The rims are delivered ready to install including wheel bearings. Sizes from 3.5" x 17 (18) to 12.5" x 18. Other sizes available on request! Scope of delivery: Motorcycle rim, ready for installation, incl. wheel bearings TÜV documents: technical drawing, material specification - here a TÜV-Einzelabnahme is required (can be carried out at a competent TÜV office on site, alternatively at our premises by appointment)

3-part custom motorcycle wheel type 16 from our company, available for almost all motorcycles - whether single or double arm swingarm. (Wheels for single-sided swingarms are usually asymmetrical, i.e. the outer rim base is narrower than the inner rim base. This can only be determined after measuring the original rims) Important: We manufacture the rims ourselves, which means we can respond to detailed customer requests. So if you have a special design idea - we can make it a reality! We offer here in the store the most common variants of our rims, but are able to produce special designs of all kinds. So if you are interested, please send us an email or give us a call. We need the original wheels of your vehicle for the measurement. Please remove brake discs and tires, we also don't need the sprocket carrier for the measurement. Simply send them well packed by mail to RF-Biketech GmbH, Mühlweg 10, 97720 Nuedlingen, Germany. Once we have taken the measurements, we will return the wheels to you intact by mail. The rims are made of high-strength aluminum using CNC technology here inhouse. We mill the inner part of the rim completely ourselves, the rim beds are delivered to us. The inner part and the rim beds are then screwed together (VA screws) and glued. The tires are mounted tubeless. The hub adapters for the rims are included in the price. Sprocket carrier of the original rims is further used. Otherwise the wheels are plug & play ready to install, no new wheel spacers or other modifications necessary (of course only if original sizes are chosen). If you choose wider wheels, rear swingarm or triple clamps have to be changed as well - we offer wide swingarms as well as our own triple clamps here in the store. Just give us a call or write an email if you have any questions, we'll be happy to advise you! Surface info: Rims can be delivered high gloss polished, bicolor (rims are coated in color and the contours of the inner part then milled again, so that these edges and pockets appear again in aluminum silver) or also in RAL powder coated. We offer here in the store only black-matte and black-glossy, other colors quite simply ask by mail and we send you an offer. The rims are delivered ready to install including wheel bearings. Sizes from 3.5" x 17 (18) to 12.5" x 18. Other sizes available on request! Scope of delivery: Motorcycle rim, ready for installation, incl. wheel bearings TÜV documents: technical drawing, material specification - here a TÜV-Einzelabnahme is required (can be carried out at a competent TÜV office on site, alternatively at our premises by appointment)

3-part custom motorcycle wheel type 3 from our company, available for almost all motorcycles - whether single or double arm swingarm. (Wheels for single-sided swingarms are usually asymmetrical, i.e. the outer rim base is narrower than the inner rim base. This can only be determined after measuring the original rims) Important: We manufacture the rims ourselves, which means we can respond to detailed customer requests. So if you have a special design idea - we can make it a reality! We offer here in the store the most common variants of our rims, but are able to produce special designs of all kinds. So if you are interested, please send us an email or give us a call. We need the original wheels of your vehicle for the measurement. Please remove brake discs and tires, we also don't need the sprocket carrier for the measurement. Simply send them well packed by mail to RF-Biketech GmbH, Mühlweg 10, 97720 Nuedlingen, Germany. Once we have taken the measurements, we will return the wheels to you intact by mail. The rims are made of high-strength aluminum using CNC technology here inhouse. We mill the inner part of the rim completely ourselves, the rim beds are delivered to us. The inner part and the rim beds are then screwed together (VA screws) and glued. The tires are mounted tubeless. The hub adapters for the rims are included in the price. Sprocket carrier of the original rims is further used. Otherwise the wheels are plug & play ready to install, no new wheel spacers or other modifications necessary (of course only if original sizes are chosen). If you choose wider wheels, rear swingarm or triple clamps have to be changed as well - we offer wide swingarms as well as our own triple clamps here in the store. Just give us a call or write an email if you have any questions, we'll be happy to advise you! Surface info: Rims can be delivered high gloss polished, bicolor (rims are coated in color and the contours of the inner part then milled again, so that these edges and pockets appear again in aluminum silver) or also in RAL powder coated. We offer here in the store only black-matte and black-glossy, other colors quite simply ask by mail and we send you an offer. The rims are delivered ready to install including wheel bearings. Sizes from 3.5" x 17 (18) to 12.5" x 18. Other sizes available on request! Scope of delivery: Motorcycle rim, ready for installation, incl. wheel bearings TÜV documents: technical drawing, material specification - here a TÜV-Einzelabnahme is required (can be carried out at a competent TÜV office on site, alternatively at our premises by appointment)

3-part custom motorcycle wheel type 4 from our company, available for almost all motorcycles - whether single or double arm swingarm. (Wheels for single-sided swingarms are usually asymmetrical, i.e. the outer rim base is narrower than the inner rim base. This can only be determined after measuring the original rims) Important: We manufacture the rims ourselves, which means we can respond to detailed customer requests. So if you have a special design idea - we can make it a reality! We offer here in the store the most common variants of our rims, but are able to produce special designs of all kinds. So if you are interested, please send us an email or give us a call. We need the original wheels of your vehicle for the measurement. Please remove brake discs and tires, we also don't need the sprocket carrier for the measurement. Simply send them well packed by mail to RF-Biketech GmbH, Mühlweg 10, 97720 Nuedlingen, Germany. Once we have taken the measurements, we will return the wheels to you intact by mail. The rims are made of high-strength aluminum using CNC technology here inhouse. We mill the inner part of the rim completely ourselves, the rim beds are delivered to us. The inner part and the rim beds are then screwed together (VA screws) and glued. The tires are mounted tubeless. The hub adapters for the rims are included in the price. Sprocket carrier of the original rims is further used. Otherwise the wheels are plug & play ready to install, no new wheel spacers or other modifications necessary (of course only if original sizes are chosen). If you choose wider wheels, rear swingarm or triple clamps have to be changed as well - we offer wide swingarms as well as our own triple clamps here in the store. Just give us a call or write an email if you have any questions, we'll be happy to advise you! Surface info: Rims can be delivered high gloss polished, bicolor (rims are coated in color and the contours of the inner part then milled again, so that these edges and pockets appear again in aluminum silver) or also in RAL powder coated. We offer here in the store only black-matte and black-glossy, other colors quite simply ask by mail and we send you an offer. The rims are delivered ready to install including wheel bearings. Sizes from 3.5" x 17 (18) to 12.5" x 18. Other sizes available on request! Scope of delivery: Motorcycle rim, ready for installation, incl. wheel bearings TÜV documents: technical drawing, material specification - here a TÜV-Einzelabnahme is required (can be carried out at a competent TÜV office on site, alternatively at our premises by appointment)

3-part custom motorcycle wheel type 6 from our company, available for almost all motorcycles - whether single or double arm swingarm. (Wheels for single-sided swingarms are usually asymmetrical, i.e. the outer rim base is narrower than the inner rim base. This can only be determined after measuring the original rims) Important: We manufacture the rims ourselves, which means we can respond to detailed customer requests. So if you have a special design idea - we can make it a reality! We offer here in the store the most common variants of our rims, but are able to produce special designs of all kinds. So if you are interested, please send us an email or give us a call. We need the original wheels of your vehicle for the measurement. Please remove brake discs and tires, we also don't need the sprocket carrier for the measurement. Simply send them well packed by mail to RF-Biketech GmbH, Mühlweg 10, 97720 Nuedlingen, Germany. Once we have taken the measurements, we will return the wheels to you intact by mail. The rims are made of high-strength aluminum using CNC technology here inhouse. We mill the inner part of the rim completely ourselves, the rim beds are delivered to us. The inner part and the rim beds are then screwed together (VA screws) and glued. The tires are mounted tubeless. The hub adapters for the rims are included in the price. Sprocket carrier of the original rims is further used. Otherwise the wheels are plug & play ready to install, no new wheel spacers or other modifications necessary (of course only if original sizes are chosen). If you choose wider wheels, rear swingarm or triple clamps have to be changed as well - we offer wide swingarms as well as our own triple clamps here in the store. Just give us a call or write an email if you have any questions, we'll be happy to advise you! Surface info: Rims can be delivered high gloss polished, bicolor (rims are coated in color and the contours of the inner part then milled again, so that these edges and pockets appear again in aluminum silver) or also in RAL powder coated. We offer here in the store only black-matte and black-glossy, other colors quite simply ask by mail and we send you an offer. The rims are delivered ready to install including wheel bearings. Sizes from 3.5" x 17 (18) to 12.5" x 18. Other sizes available on request! Scope of delivery: Motorcycle rim, ready for installation, incl. wheel bearings TÜV documents: technical drawing, material specification - here a TÜV-Einzelabnahme is required (can be carried out at a competent TÜV office on site, alternatively at our premises by appointment)

3-part custom motorcycle wheel type 7 from our company, available for almost all motorcycles - whether single or double arm swingarm. (Wheels for single-sided swingarms are usually asymmetrical, i.e. the outer rim base is narrower than the inner rim base. This can only be determined after measuring the original rims) Important: We manufacture the rims ourselves, which means we can respond to detailed customer requests. So if you have a special design idea - we can make it a reality! We offer here in the store the most common variants of our rims, but are able to produce special designs of all kinds. So if you are interested, please send us an email or give us a call. We need the original wheels of your vehicle for the measurement. Please remove brake discs and tires, we also don't need the sprocket carrier for the measurement. Simply send them well packed by mail to RF-Biketech GmbH, Mühlweg 10, 97720 Nuedlingen, Germany. Once we have taken the measurements, we will return the wheels to you intact by mail. The rims are made of high-strength aluminum using CNC technology here inhouse. We mill the inner part of the rim completely ourselves, the rim beds are delivered to us. The inner part and the rim beds are then screwed together (VA screws) and glued. The tires are mounted tubeless. The hub adapters for the rims are included in the price. Sprocket carrier of the original rims is further used. Otherwise the wheels are plug & play ready to install, no new wheel spacers or other modifications necessary (of course only if original sizes are chosen). If you choose wider wheels, rear swingarm or triple clamps have to be changed as well - we offer wide swingarms as well as our own triple clamps here in the store. Just give us a call or write an email if you have any questions, we'll be happy to advise you! Surface info: Rims can be delivered high gloss polished, bicolor (rims are coated in color and the contours of the inner part then milled again, so that these edges and pockets appear again in aluminum silver) or also in RAL powder coated. We offer here in the store only black-matte and black-glossy, other colors quite simply ask by mail and we send you an offer. The rims are delivered ready to install including wheel bearings. Sizes from 3.5" x 17 (18) to 12.5" x 18. Other sizes available on request! Scope of delivery: Motorcycle rim, ready for installation, incl. wheel bearings TÜV documents: technical drawing, material specification - here a TÜV-Einzelabnahme is required (can be carried out at a competent TÜV office on site, alternatively at our premises by appointment)

3-part custom motorcycle wheel type 9 from our company, available for almost all motorcycles - whether single or double arm swingarm. (Wheels for single-sided swingarms are usually asymmetrical, i.e. the outer rim base is narrower than the inner rim base. This can only be determined after measuring the original rims) Important: We manufacture the rims ourselves, which means we can respond to detailed customer requests. So if you have a special design idea - we can make it a reality! We offer here in the store the most common variants of our rims, but are able to produce special designs of all kinds. So if you are interested, please send us an email or give us a call. We need the original wheels of your vehicle for the measurement. Please remove brake discs and tires, we also don't need the sprocket carrier for the measurement. Simply send them well packed by mail to RF-Biketech GmbH, Mühlweg 10, 97720 Nuedlingen, Germany. Once we have taken the measurements, we will return the wheels to you intact by mail. The rims are made of high-strength aluminum using CNC technology here inhouse. We mill the inner part of the rim completely ourselves, the rim beds are delivered to us. The inner part and the rim beds are then screwed together (VA screws) and glued. The tires are mounted tubeless. The hub adapters for the rims are included in the price. Sprocket carrier of the original rims is further used. Otherwise the wheels are plug & play ready to install, no new wheel spacers or other modifications necessary (of course only if original sizes are chosen). If you choose wider wheels, rear swingarm or triple clamps have to be changed as well - we offer wide swingarms as well as our own triple clamps here in the store. Just give us a call or write an email if you have any questions, we'll be happy to advise you! Surface info: Rims can be delivered high gloss polished, bicolor (rims are coated in color and the contours of the inner part then milled again, so that these edges and pockets appear again in aluminum silver) or also in RAL powder coated. We offer here in the store only black-matte and black-glossy, other colors quite simply ask by mail and we send you an offer. The rims are delivered ready to install including wheel bearings. Sizes from 3.5" x 17 (18) to 12.5" x 18. Other sizes available on request! Scope of delivery: Motorcycle rim, ready for installation, incl. wheel bearings TÜV documents: technical drawing, material specification - here a TÜV-Einzelabnahme is required (can be carried out at a competent TÜV office on site, alternatively at our premises by appointment)

The offset kit contains all the necessary parts to install the RFB Buell wide swingarm with 280/300 rear tires. Scope of delivery: Drive belt 143 mm longer than original belt Pulley wheel offset kit (if original pulley wheel is delivered) CNC-milled engine cover with thrust bearing and spacers and bolts Rear pulley wheel spacer with screws Extended steel flex brake pipe

This offset pulley from NLC is needed for our 240 conversion kit for the Indian Scout. Scope of delivery: Offset pulley

This steel fender was specially developed for a 240 tire and can be bolted to the original frame mounts plug & play. The original fender struts are reused here. We also offer the corresponding rear wheel rim and rear swingarm here in the store. Scope of delivery: Steel fender, unpainted Fastening screws TÜV sample certificate from an identical vehicle TÜV information (for Germany): A TÜV sample certificate from an identical vehicle is supplied for TÜV-Einzelabnahme. If you have any further questions about TÜV approval, please contact us.

We deliver a CNC milled aluminum swingarm from our own production - the swingarm fits without any modifications to the Buell XB 1, i.e. bearing and shock mount are exactly identical to the original swingarm. The swingarm is approx. 143 mm longer than the original swingarm and can only be installed in combination with our Offset Kit (available in this category in our store). The extended swingarm massively improves the straight-line stability of the vehicle and still loses nothing in terms of handling. Scope of delivery: Ready-to-install swingarm with integrated oil tank and built-in bearings, black powder coated Rear wheel stub axle Rear wheel spacer Documents for individual TÜV approval Other colors or surface treatments (e.g. high gloss polishing) are possible on request by mail or phone.

We widen the original cast wheels of your motorcycle! The advantage is that you can then drive wider or even changed in diameter wheels / tires without having to make further changes to the bike. The wheel hubs remain unchanged, only the rim beds are changed. Of course you have to take into account the clearance wheel-chain, wheel-cardan, wheel-belt and the width of the swingarm. In most cases, the original rim widening for motorcycles is also the most cost-efficient way to realize wheel size changes. For widening, the original rim beds are turned on special lathes and then machine-welded to corresponding larger rim beds using the TIG welding process. The weld is no longer visible in the outer area of the rim beds and the rim looks like a "normal" rim. A strength certificate with identification is enclosed. Note: If you are unsure whether your rim can be widened, send us a picture by mail in advance! We will be happy to advise you. Here's why: Cast rims, which have a rim bed, into which no cast spokes run from the inner star, can generally be widened (that's most rims). However, there are also rims where the cast spokes merge into the rim bed. Here, it is usually difficult or even impossible to widen the wheel. Furthermore, the following applies: A rim can be widened by a maximum of 2.0" in the same diameter, e.g. 3.5" x 17" to a maximum of 5.5" x 17". Wider is also possible, but then the diameter of the rim must be increased by 1", e.g. 5.5" x 17" to 10.0" x 18". The wheels are blasted before processing and must be resurfaced after widening, which we of course also offer - just select the desired variant (coated, painted, polished). Our variants here in the store are always based on delivered 17" or 18" wheels. Other dimensions on request by mail. Please send or deliver wheels without attachments (brake discs, tires, sprocket carrier) by mail to us. The procedure: Place your order here in the store or send us an e-mail request Send the bike to us by mail (print out the order confirmation and put it in the package) to the address RF-Biketech GmbH, Mühlweg 10, 97720 Nüdlingen, Germany We widen the wheel as desired and treat the surface depending on the variant We send the widened wheel back to you Scope of delivery: Widened wheel (wheel bearings are not mounted but attached in the package) technical report with identification (Festigkeitsgutachten) for TÜV (Germany)

Stainless steel spoke rim set with 60 spokes for the Triumph Rocket 3 R and GT from model year 2019 (we can also offer spoke rims for the predecessor model Rocket 3, you can find these in the category Universal Custom Parts -> Wheels/Wheel hubs/Rims here in the store. The wheel set is plug & play ready. The original rim cover of the rear wheel is reused. The surfaces of the wheel hubs and rim rings can be selected, the spokes themselves always remain polished in VA. Due to the high torque of the Rocket, we have 60 spokes, which are thicker in diameter than the spokes we normally use. Tire sizes are different from the original (other sizes on request!): Rear: 9.0 x 17 für 240/45 VR17 Front: 4.0 x 18 für 150/70 VR18 Scope of delivery: Rims rear and front 2x bolts for rear wheel drive screw connection on swingarm (must be replaced) TÜV: TÜV-Einzelabnahme required! (for Germany) Strength certificate rims and TÜV sample certificate of identical vehicle with corresponding TÜV entry

We offer the widening of the original swingarm in order to be able to install a 240 tire in the Indian Scout. The original swingarm must be sent to us for this - it is then widened in a specially made welding gauge and then powder-coated. The spacers required for installation are supplied. This widening makes it possible to fit an 8.5 x 17 inch wheel (available to order here in the store) in the middle of the vehicle. It is necessary to order the corresponding offset pulley (also available here in the store). Procedure: Pack the original swing arm and send it to us (RF-Biketech GmbH, Mühlweg 10, 97720 Nüdlingen, Germany) We widen the swingarm The swingarm gets powdercoated again We send the finished swingarm back to you Scope of delivery: Spacers for installation Extended swingarm/frame axle TÜV-sample certificate of an identical vehicle (for Germany) TÜV-Einzelabnahme

Here's our inhouse CNC-machined triple clamp set type 1 (Triple clamp sizes: top 30 mm, 1 clamping, below 35 mm, 2 clampings) made from high strength aluminum. Our triple clamp types from type 1 to type 5 are universal triple clamps/fork bridges, which are individually manufactured by us according to your wishes. For even more individual inquiries, please feel free to contact us by mail or phone, we are always happy to advise you and send you an offer by mail. We manufacture triple clamps for almost all standpipe distances, clamp diameters and offsets. Also we can consider original cockpits and ignition locks as well as after sale cockpits that are integrated in the triple clamp (f.e. motoscope pro). Fork covers: It is also possible to prepare the triple clamp for fork covers. Because we have to consider additional things here, please contact us via e-mail or phone. With a fork conversion the following criteria are always to be considered: Which brake system should be used in the fork conversion? (The original brake system or the brake system matching the fork? Both are possible, but the brake system matching the fork is recommended.) Which front wheel will be used? (The original front wheel or the wheel matching the fork? The wheel matching the fork is recommended.) Clamping diameter of the fork top and bottom Fork tube distance center - center Offset (center steering tube to center fork tube) Dimension of the steering tube (best with a sketch, which you send us in addition to the order via e-mail) Dimension of the steering stops (best with a sketch, which you send us in addition to the order via e-mail) If you are technically proficient enough to measure the desired triple clamp yourself, then please download the following form and send it to us filled out by e-mail with your order number from the store (if you have configured and ordered something here) to info@rf-biketech.de. You then select "Production via sketch" in the variants. We add the missing dimensions (f.e. the heights of the triple clamps etc.) ourselves when we manufacture the triple clamp. Download Form If you do not have the detailed measurements or are unsure, you can alternatively send the parts to us and we measure them ourselves. In that case, please select "Sample via mail" in the variants. For the sample package we need the following parts from you: lower original triple clamp of the bike lower triple clamp of the new fork upper original triple clamp (only if original steering lock and original cockpit are reinstalled) Of course you will get the parts back intact. They serve exclusively for the measurement. These measurements are so important, because during the production of your desired triple clamp the distance measurements can be taken into account (fork tube distance to each other), so that later the wheel and the brake system can be installed without further adapters. The steering stops or speedometer holders on the respective pictures here will of course look different on your triple clamp than on our sample pictures. Scope of delivery: Ready-to-install triple clamp set with pressed-in steering tube (stainless steel) Triple clamp sizes: top 30 mm, 1 clamping, below 35 mm, 2 clampings TÜV certificate (technical report)

Here's our inhouse CNC-machined triple clamp set type 2 (Triple clamp sizes: top 40 mm, 2 clamping, below 60 mm, 3 clampings) made from high strength aluminum. Our triple clamp types from type 1 to type 6 are universal triple clamps/fork bridges, which are individually manufactured by us according to your wishes. For even more individual inquiries, please feel free to contact us by mail or phone, we are always happy to advise you and send you an offer by mail. We manufacture triple clamps for almost all standpipe distances, clamp diameters and offsets. Also we can consider original cockpits and ignition locks as well as after sale cockpits that are integrated in the triple clamp (f.e. motoscope pro). Fork covers: It is also possible to prepare the triple clamp for fork covers. Because we have to consider additional things here, please contact us via e-mail or phone. With a fork conversion the following criteria are always to be considered: Which brake system should be used in the fork conversion? (The original brake system or the brake system matching the fork? Both are possible, but the brake system matching the fork is recommended.) Which front wheel will be used? (The original front wheel or the wheel matching the fork? The wheel matching the fork is recommended.) Clamping diameter of the fork top and bottom Fork tube distance center - center Offset (center steering tube to center fork tube) Dimension of the steering tube (best with a sketch, which you send us in addition to the order via e-mail) Dimension of the steering stops (best with a sketch, which you send us in addition to the order via e-mail) If you are technically proficient enough to measure the desired triple clamp yourself, then please download the following form and send it to us filled out by e-mail with your order number from the store (if you have configured and ordered something here) to info@rf-biketech.de. You then select "Production via sketch" in the variants. We add the missing dimensions (f.e. the heights of the triple clamps etc.) ourselves when we manufacture the triple clamp. Download Form If you do not have the detailed measurements or are unsure, you can alternatively send the parts to us and we measure them ourselves. In that case, please select "Sample via mail" in the variants. For the sample package we need the following parts from you: lower original triple clamp of the bike lower triple clamp of the new fork upper original triple clamp (only if original steering lock and original cockpit are reinstalled) Of course you will get the parts back intact. They serve exclusively for the measurement. These measurements are so important, because during the production of your desired triple clamp the distance measurements can be taken into account (fork tube distance to each other), so that later the wheel and the brake system can be installed without further adapters. The steering stops or speedometer holders on the respective pictures here will of course look different on your triple clamp than on our sample pictures. Scope of delivery: Ready-to-install triple clamp set with pressed-in steering tube (stainless steel) Triple clamp sizes: top 40 mm, 2 clamping, below 60 mm, 3 clampings TÜV certificate (technical report)

Here's our inhouse CNC-machined triple clamp set type 3 (Triple clamp sizes: top 70- 80 mm, 4 clamping, below 80 mm, 4 clampings) made from high strength aluminum. Our triple clamp types from type 1 to type 6 are universal triple clamps/fork bridges, which are individually manufactured by us according to your wishes. For even more individual inquiries, please feel free to contact us by mail or phone, we are always happy to advise you and send you an offer by mail. We manufacture triple clamps for almost all standpipe distances, clamp diameters and offsets. Also we can consider original cockpits and ignition locks as well as after sale cockpits that are integrated in the triple clamp (f.e. motoscope pro). Fork covers: It is also possible to prepare the triple clamp for fork covers. Because we have to consider additional things here, please contact us via e-mail or phone. With a fork conversion the following criteria are always to be considered: Which brake system should be used in the fork conversion? (The original brake system or the brake system matching the fork? Both are possible, but the brake system matching the fork is recommended.) Which front wheel will be used? (The original front wheel or the wheel matching the fork? The wheel matching the fork is recommended.) Clamping diameter of the fork top and bottom Fork tube distance center - center Offset (center steering tube to center fork tube) Dimension of the steering tube (best with a sketch, which you send us in addition to the order via e-mail) Dimension of the steering stops (best with a sketch, which you send us in addition to the order via e-mail) If you are technically proficient enough to measure the desired triple clamp yourself, then please download the following form and send it to us filled out by e-mail with your order number from the store (if you have configured and ordered something here) to info@rf-biketech.de. You then select "Production via sketch" in the variants. We add the missing dimensions (f.e. the heights of the triple clamps etc.) ourselves when we manufacture the triple clamp. Download Form If you do not have the detailed measurements or are unsure, you can alternatively send the parts to us and we measure them ourselves. In that case, please select "Sample via mail" in the variants. For the sample package we need the following parts from you: lower original triple clamp of the bike lower triple clamp of the new fork upper original triple clamp (only if original steering lock and original cockpit are reinstalled) Of course you will get the parts back intact. They serve exclusively for the measurement. These measurements are so important, because during the production of your desired triple clamp the distance measurements can be taken into account (fork tube distance to each other), so that later the wheel and the brake system can be installed without further adapters. The steering stops or speedometer holders on the respective pictures here will of course look different on your triple clamp than on our sample pictures. Scope of delivery: Ready-to-install triple clamp set with pressed-in steering tube (stainless steel) Triple clamp sizes: top 70- 80 mm, 4 clamping, below 80 mm, 4 clampings TÜV certificate (technical report)

Here's our inhouse CNC-machined triple clamp set type 4 (Triple clamp sizes: top 80 mm, 4 clampings, below 100 mm, 5 clampings) made from high strength aluminum. Our triple clamp types from type 1 to type 6 are universal triple clamps/fork bridges, which are individually manufactured by us according to your wishes. For even more individual inquiries, please feel free to contact us by mail or phone, we are always happy to advise you and send you an offer by mail. We manufacture triple clamps for almost all standpipe distances, clamp diameters and offsets. Also we can consider original cockpits and ignition locks as well as after sale cockpits that are integrated in the triple clamp (f.e. motoscope pro). Fork covers: It is also possible to prepare the triple clamp for fork covers. Because we have to consider additional things here, please contact us via e-mail or phone. With a fork conversion the following criteria are always to be considered: Which brake system should be used in the fork conversion? (The original brake system or the brake system matching the fork? Both are possible, but the brake system matching the fork is recommended.) Which front wheel will be used? (The original front wheel or the wheel matching the fork? The wheel matching the fork is recommended.) Clamping diameter of the fork top and bottom Fork tube distance center - center Offset (center steering tube to center fork tube) Dimension of the steering tube (best with a sketch, which you send us in addition to the order via e-mail) Dimension of the steering stops (best with a sketch, which you send us in addition to the order via e-mail) If you are technically proficient enough to measure the desired triple clamp yourself, then please download the following form and send it to us filled out by e-mail with your order number from the store (if you have configured and ordered something here) to info@rf-biketech.de. You then select "Production via sketch" in the variants. We add the missing dimensions (f.e. the heights of the triple clamps etc.) ourselves when we manufacture the triple clamp. Download Form If you do not have the detailed measurements or are unsure, you can alternatively send the parts to us and we measure them ourselves. In that case, please select "Sample via mail" in the variants. For the sample package we need the following parts from you: lower original triple clamp of the bike lower triple clamp of the new fork upper original triple clamp (only if original steering lock and original cockpit are reinstalled) Of course you will get the parts back intact. They serve exclusively for the measurement. These measurements are so important, because during the production of your desired triple clamp the distance measurements can be taken into account (fork tube distance to each other), so that later the wheel and the brake system can be installed without further adapters. The steering stops or speedometer holders on the respective pictures here will of course look different on your triple clamp than on our sample pictures. Scope of delivery: Ready-to-install triple clamp set with pressed-in steering tube (stainless steel) Triple clamp sizes: top 80 mm, 4 clampings, below 100 mm, 5 clampings TÜV certificate (technical report)

Here's our inhouse CNC-machined triple clamp set type 5 (Triple clamp sizes: top and below 30-35 mm, 2 clampings) made from high strength aluminum. Our triple clamp types from type 1 to type 6 are universal triple clamps/fork bridges, which are individually manufactured by us according to your wishes. For even more individual inquiries, please feel free to contact us by mail or phone, we are always happy to advise you and send you an offer by mail. We manufacture triple clamps for almost all standpipe distances, clamp diameters and offsets. Also we can consider original cockpits and ignition locks as well as after sale cockpits that are integrated in the triple clamp (f.e. motoscope pro). Fork covers: It is also possible to prepare the triple clamp for fork covers. Because we have to consider additional things here, please contact us via e-mail or phone. The type 5 triple clamp was developed primarily for length compensation for forks that are too short. The cranking (30 or 35 mm) lengthens the fork and more ground clearance is achieved. This also affects the trail accordingly. With a fork conversion the following criteria are always to be considered: Which brake system should be used in the fork conversion? (The original brake system or the brake system matching the fork? Both are possible, but the brake system matching the fork is recommended.) Which front wheel will be used? (The original front wheel or the wheel matching the fork? The wheel matching the fork is recommended.) Clamping diameter of the fork top and bottom Fork tube distance center - center Offset (center steering tube to center fork tube) Dimension of the steering tube (best with a sketch, which you send us in addition to the order via e-mail) Dimension of the steering stops (best with a sketch, which you send us in addition to the order via e-mail) If you are technically proficient enough to measure the desired triple clamp yourself, then please download the following form and send it to us filled out by e-mail with your order number from the store (if you have configured and ordered something here) to info@rf-biketech.de. You then select "Production via sketch" in the variants. We add the missing dimensions (f.e. the heights of the triple clamps etc.) ourselves when we manufacture the triple clamp. Download Form If you do not have the detailed measurements or are unsure, you can alternatively send the parts to us and we measure them ourselves. In that case, please select "Sample via mail" in the variants. For the sample package we need the following parts from you: lower original triple clamp of the bike lower triple clamp of the new fork upper original triple clamp (only if original steering lock and original cockpit are reinstalled) Of course you will get the parts back intact. They serve exclusively for the measurement. These measurements are so important, because during the production of your desired triple clamp the distance measurements can be taken into account (fork tube distance to each other), so that later the wheel and the brake system can be installed without further adapters. The steering stops or speedometer holders on the respective pictures here will of course look different on your triple clamp than on our sample pictures. Scope of delivery: Ready-to-install triple clamp set with pressed-in steering tube (stainless steel) Triple clamp sizes: top and below 30-35 mm, 2 clampings TÜV certificate (technical report)

Here's our inhouse CNC-machined triple clamp set type 6 (Triple clamp sizes: top 40 mm, 2 clamping, below 60 mm, 3 clampings) made from high strength aluminum. Our triple clamp types from type 1 to type 6 are universal triple clamps/fork bridges, which are individually manufactured by us according to your wishes. For even more individual inquiries, please feel free to contact us by mail or phone, we are always happy to advise you and send you an offer by mail. We manufacture triple clamps for almost all standpipe distances, clamp diameters and offsets. Also we can consider original cockpits and ignition locks as well as after sale cockpits that are integrated in the triple clamp (f.e. motoscope pro). Fork covers: It is also possible to prepare the triple clamp for fork covers. Because we have to consider additional things here, please contact us via e-mail or phone. With a fork conversion the following criteria are always to be considered: Which brake system should be used in the fork conversion? (The original brake system or the brake system matching the fork? Both are possible, but the brake system matching the fork is recommended.) Which front wheel will be used? (The original front wheel or the wheel matching the fork? The wheel matching the fork is recommended.) Clamping diameter of the fork top and bottom Fork tube distance center - center Offset (center steering tube to center fork tube) Dimension of the steering tube (best with a sketch, which you send us in addition to the order via e-mail) Dimension of the steering stops (best with a sketch, which you send us in addition to the order via e-mail) If you are technically proficient enough to measure the desired triple clamp yourself, then please download the following form and send it to us filled out by e-mail with your order number from the store (if you have configured and ordered something here) to info@rf-biketech.de. You then select "Production via sketch" in the variants. We add the missing dimensions (f.e. the heights of the triple clamps etc.) ourselves when we manufacture the triple clamp. Download Form If you do not have the detailed measurements or are unsure, you can alternatively send the parts to us and we measure them ourselves. In that case, please select "Sample via mail" in the variants. For the sample package we need the following parts from you: lower original triple clamp of the bike lower triple clamp of the new fork upper original triple clamp (only if original steering lock and original cockpit are reinstalled) Of course you will get the parts back intact. They serve exclusively for the measurement. These measurements are so important, because during the production of your desired triple clamp the distance measurements can be taken into account (fork tube distance to each other), so that later the wheel and the brake system can be installed without further adapters. The steering stops or speedometer holders on the respective pictures here will of course look different on your triple clamp than on our sample pictures. Scope of delivery: Ready-to-install triple clamp set with pressed-in steering tube (stainless steel) Triple clamp sizes: top 40 mm, 2 clamping, below 60 mm, 3 clampings TÜV certificate (technical report)

We widen your rear wheel rim to 10.0" x 18" - the following tires can then be driven: 280/35 VR 18 or 300/35 VR 18. After widening the rim is sandblasted and must be powdercoated or painted again. Delivery incl. TÜV certificate. Please deliver rim without tires without brake disc and pulley wheel. Note: The process is simple: Just send your rim (without tires, without brake disc, without pulley wheel) to us by mail (Address: RF-Biketech GmbH, Muehlweg 10, 97720 Nuedlingen, Germany). We take care of the widening and send the rim back to you. If you have any more questions, please do not hesitate to contact us via mail or phone.